I’ve found slurry to sometimes be counterproductive. The main benefit of natural stones, beyond being more pleasant in use, is they often impart an edge that’s less harsh. Try starting with a good 12k edge then do a dozen or so light laps on the lune and see what that gets you. With any luck it’s nearly as sharp as right off the synth but nicer on the skin.
It is indeed! And aha, symmetrical. Thanks, that was both satisfying and inspiring. Was already eyeing Roman’s blades and now you’ve made it dangerously easy to say “I’ll have one like this but 7/8 and smiling a bit”…
I’d be curious to see pics of that if it’d be convenient–seen folding kamis but none I’d describe as especially hollow…
!straight_razors@sub.wetshaving.social is …pretty niche. But yes, some of us still use straight razors. Often ones that are over a century old. And it’s not as dangerous as you might assume–in fact an edge carefully honed by hand can be easier on the skin than what comes off a factory line wrapped in too much plastic.
Excellent, Just wait, the next shaves will likely be even better–I find the first shave on these blades is often a bit harsh by comparison. Luckily they last longer than DE blades so I don’t have to endure it very often. Palm-stropping new ones (carefully!) also helps a fair bit.
Keep an eye out for a Micromatic Clog-pruf. They’re my favourite Gem razor and still give good feedback but not quite so loud. Plus the twist-to-open mechanism is cool https://wegianwetshaving.com/2020/03/the-patent-for-the-gem-micromatic
Unfortunately this is complicated by the fact that turmeric is perhaps more likely than most spices to have lead contamination as not only is there the usual possibility of contaminated soil there is also a somewhat common practice of using lead chromate to dye it a brighter colour: https://ehp.niehs.nih.gov/doi/abs/10.1289/isesisee.2018.P02.3490
I prefer the Clog-pruf, you might just have to get all three Micromatics to make sure… @snooting@sub.wetshaving.social does your MMOC have the raised dots that turn it down a bit?
You know, I’ve seen you mention this a time or two and I think noticed it elsewhere but still have yet to try it. Next razor I’m going to try and remember to bring some peanuts around. Usually I just try to get it shaving arm hair to determine if a bevel is set and then I cut an unsupported strand of hair as the final test but this does seem more convenient and might offer better feedback for the stages in between.
I looked to your videos for a bit more detail and found this, thanks: https://www.youtube.com/watch?v=ieTUQM0YwZA
Also, I’m curious which microscope you use? …nevermind, you answer in a comment here https://www.youtube.com/watch?v=hmD7UJ6e0II&lc=Ugz6_cFe2Rd5nqrJzZp4AaABAg.A86bp_jlZxrA87yuAG-1oY that it’s this one https://www.dinolite.us/products/usb-microscopes/am73515mt8a/
Great, looking forward to the new decor whenever you get a sec. No hurry of course, never wise to hurry when straight razors are involved.
I tossed in a different thumbnail on the straight razor sub because I was a bit sick of it being the same image but I’ve not the level of interest in photography your SotD photos clearly exhibit so I’d be happy to see you swap out the super generic banner if you’d still be interested. Also not partial to the thumbnail I chose beyond the general idea that they not be the same thing and that it’d be kind of neat if the thumbnail showed the grind of a razor toe-on as the spine-as-honing-guide is very core to what makes a straight razor.
Oh neat, didn’t know they did a titanium one. Was it just that special edition or did it become a regular product at some point?
Unfortunately I think the best we can do with the situation is appreciate that they ever bothered to make the machined ones and that they are almost certainly subsidised by the zamac. Which is also why the price isn’t that far apart: few would buy the machined one if they sold it at the same margins as the zinc alloy.
It really is exhausting though. Every time I make a purchase decision I have to be skeptical because I might be getting the zamac-with-fancy-handle version of whatever product or service I’m trying to buy. Avoiding that takes time which is how they sell all this junk at a high margin. Especially with how we’ve integrated almost every facet of life into the economy. Contributes a bit to a sense of despair. So I try to appreciate the people that do sincere work and, instead of being frustrated by it, try to consider the time it takes to winnow the quality offerings from the grift as doing my part to signal a better direction for society.
Aha! I knew it! I had this trepidation when I sold this one https://pixelfed.social/i/web/post/748289303255129698 especially because they also took this very similar one https://pixelfed.social/i/web/post/748289996039802817 …and I guess it’s probably for the best I abandon the foolish notions I had when I listed this https://imgur.com/a/mardor-z12y8cw and it was especially foolhardy to have ever considered parting with https://imgur.com/a/chassaigne-k0Fy4tt 🤔
But it’s also satisfying to set a new bevel, just not the same if it was already shaving fine (not to mention wasteful). And honing as a service seems less relaxing for myriad reasons. So compromises must be made. Thankfully(?) I’ve slowed a fair bit since the initial burst when I was getting into it, settling into a bit of an equilibrium with a handful in and out each year.
My honing enthusiasm provided too much rationalisation for razor acquisition and so I have …several. The winnowing process is ongoing and I’m proud to have sold 5 x 5/8 last week.
6/8 is harder because I like them more. Lately I’m wondering: Do I really need two 6/8 hollow-but-stiff round point French blades?
I’m partial to the Grelot. I do appreciate that it’s a bit more hollow and as a Canadian I enjoy the etch. Plus it’s my only nice Grelot and there’s some cachet there. And it’s in better shape. But there’s just something to the TI and it’s similarly my best TI and the pitting isn’t anywhere important so just sorta adds character. And it’s more towards a quarter hollow so …sort of a different thing altogether?
Inconclusive. More study required. Luckily they don’t take a lot of space.
Also: I’m always curious to see the grind toe-on every time I see a picture of a straight razor and that shot should somehow always be included in the metadata or something :)
Coooooool. Thanks for sharing.
This seems like a really nice size, good compromise between heft/lather handling and agility. Plus I like the jimping on it. Somehow I suspect you’ll hang on to this one.
And ya, wow, did you stumble onto a hidden cache of underappreciated and underpriced blades or did you set out to expand your collection like this?
I often see people wedging injector blades into things eg. Ender’s, Ronson, etc. but haven’t given it enough thought to guess if there’s a reasonable way to do that here.
You might also consider vintage razors, a lot of them are brass and they’ve stood the test of time to get this far.
Alternatively, if what you really want is machined stainless you can probably get it for that price from dscosmetic or yaqi on AliExpress. They have many models so it’d be worth searching out some reviews.
I’m unsurprised to see an overlap between meditation and straight razor appreciation. After all, using, honing and stropping my straights are some of my favourite meditations though I still try to keep a more formal practice.
There are also thick framebacks but they’re basically just like a light wedge so I think you’re right to prioritise the Japanese ones.
I like the look of tapered blades and was lucky enough to score one but it’s been at my brother’s place waiting for scales for a while now. One day.
Rattlers are neat but also basically feel like a light wedge however I have this one smaller one I quite like, took a nice edge, slight smile, etc. sometimes a razor just fits.
“Lancet” is what Mappin called these, but there have been a few imitators and while I’ve not tried one quite like that though I have this one with a hollowed out spine that maybe is at least in the same sort of category? Heh, actually that mailcall is pretty topical overall, even has a lather catcher.
Yes, but I have 100 FHS-10 blades and no other razor to use them in😅
Good call on the Audiostrop then, much more appealing than the Oneblade (which I never really felt drawn to in any way) and I liked the noisy feedback from it though I did move mine along as I could get a similar effect from the Wilkinson.
Edit: closing a stray image search tab I spotted this link to an especially nice lancet-ish razor.
Very cool and what a well-preserved example! Out of curiosity, did you do something like yahoo.co.jp + a parcel forwarder or was this a more straightforward eg. ebay purchase?